F.A.Q.
Home

LIMITED WARRANTY: 
Quick Draw B F Rest are guaranteed against breakage and bending of metal parts for a period of one year from date of purchase provided the product has not been altered or misused. (The Original owner must send product directly to Quick Draw Outdoor Gear enclosing name, address, reason for return and proof of purchase.) Warranty does not cover cosmetic blemishes, fading, defects in grain of metal. Warranty does NOT cover screws, rubber gate, quick slick tape or shipping cost.
Bow Fishing Quiver warranty against workmanship and structure defects for one year from the date of your purchase. 



If your Question is not answered below please fill free to contact us:


Question: What Colors does Quick Draw Bowfishing manufactured Rest come In?

Answer: Silver & Pink

Question: Does Quick draw Warnatee a product with the same design not produced by Quick Draw? 

Answer: No . Only products manufactured by Quick Draw are waranteed by Quick Draw. All products of Quick Draws will have a Quick Draw Label and logo on packaging. 

Question: Does Quick Draw warrantee against wear, blemishes or scratches ?

Answer: No, the arrow rest body is assembled by hand a scratch or two may occur but the anodized body will with-stand alot ; but scratch and wear  will occur over time eventually.

Question? Does the Pink Arrow rest pink color look exactly like the cover picture?

Answer: No, anodizing in color varies and photo colors aren't exact to the original.

Question: Can I purchase replacement screws to fit the Q.D. Rest?

Answer: Yes, We make available replacements for all screws , w/wrench’s ,, quick slick tape & rubber Gate in the  accessory pack.  (The accessory pack fits all rest that has the same exact design.)

Question: Can I purchase a replacement Rubber Gate and more Quick Slick Tape.

Answer: Yes, you can.  We sell Individual tape and gates  or the Accessory Pack. that includes both  can purchase from a Quick Draw Dealer, our web page.

Question: Do you have instruction on how to apply Rubber Gate and Quick slick tape?

 Answer: Yes, At the bottom of this page is instruction to apply quick slick tape & Rubber Gate 

Question : Can I tie to the back of my arrow using the Quick Draw Bow Fishing arrow rest?

Answer : During testing I have not had any problems; but snap backs are known to occur when tying to the back of your arrow. Due to this Quick Draw does not recommend or endorse this practice under any circumstances.

Question: Can the Quick Draw Arrow Rest be  shot without the rubber gate.

Answer: Yes,  it can be shot without the rubber gate.   But without the rubber gate the arrow is no longer captured and is subject to come off the rest. (Quick Draw does not recommend or endorse this practice.)


Question: Will the safety slide Stop hit the arrow rest on straight down shots.

Answer: NO,  Quick Draw Arrow Rest can be shot at any angle without problems as long as the Stop is position on top of the arrow and your knock point is less then 3/4 high.


Question: What will happen if I accidentally load my arrow with the Safety Slide Stop down. 

Answer: The Quick Draw Arrow Rest has designed ramps to minimize problems but not stop damage to the arrow rest or arrow.( Always check arrow rest and arrow if this occurs before shooting again.)

Question: Can I use a UNINOCK ADAPTER with Quick Draw Arrow Rest? 

Answer: If you are getting very little arrow rest contact there should be no problems. If you are getting a good bit of arrow rest contact you may need to replace your Quick Slick Tape more often then normal. 
Uninock Adapter Tips
1) Raise Nock Point
2) Taper the bottom leading edge of Adapter

Question: Can Quick Draw Arrow Rest accommodate right or left hand shooter?
Answer:yes












Quick Draw bowfishing Bond

1)Clean and dry surfaces to be bonded.
2)Apply a small amount of Quick Draw Bowfishing Bond to one of the surfaces.
(1 drop per 1 sq. inch to be bonded is recommended)

3) Press the two surfaces together for about 90 sec.( excess glue may cause longer fixture time)
Quick Draw Bowfishing Bond has been Rubber Toughened to provide Superior Shock resistance it is a very fast drying glue (not an instant glue) that will allow you a reasonable amount of time to adjust your nocks & points into your favorite position before fixture time. (75-90 sec)


Great for applying nocks & points to your bowfishing arrows!
Fast drying-Tough-Shock & Impact resistant!
No matter if you shoot in the heat or cold, Quick Draw Bowfishing Bond will do its job!
Has a Temp range from -65 to 280 °F
Fixture time of 75-90 sec / fully cured after 24hr. Store in cool dry place.


Warning:
Skin Contact:
Remove contaminated clothing. Flush affected area with soap and plenty of water for at least 15 minutes. If irritation develops or persists, seek medical attention.
Eye Contact:
Flush eyes with warm water for at least 20 minutes. Hold eyelids apart to ensure complete irrigation of the eyes. Remove contact lenses. Seek immediate medical attention.
Inhalation:
Move to fresh air. If breathing is difficult provide oxygen. If not breathing, immediately begin rescue breathing. If heart has stopped, provide cardiopulmonary resuscitation (CPR). Seek immediate medical attention.
Ingestion:
Do not induce vomiting. If vomiting occurs spontaneously, place head lower than knees, or, if unconscious, in rescue position. Seek immediate medical attention.
Notes to Physician:
Maintain adequate ventilation and oxygenation of patient.

​NOTE: Quick Draw Quick slick tape, Rubber Gate and screws will fit a PSE Snap Shot and Bass Pro Archenemy Rapid Fire. (Both PSE and Bass pro lease our patented  B.F.arrow rest design so all parts accessory will fit.)
How to replace Rubber Gate: 

Remove both small set 1/8set screws on both side of rubber gate (remove over container to catch tiny screws.) pull from inside or push through to outside, of rest.

Insert Quick Draw rubber gate through gate hole from outside into rest wall. 
Work rubber to perfect position for arrow entry so it will snap back to lock in arrow every time. 
(Use arrow size object such as pen for trial before tightening gate) Replace both set screws on both sides of gate and tighten (1-050 hex wrench) 

Using an X-blade knife or very sharp blade remove excess rubber slicing flush against outside curve of rest to make even cut. 



Decal Instructions:
1. Prep- area where decal will be placed. Clean the area thoroughly with rubbing alcohol or soap and water. ...
2. Prepare the sticker for application by firmly rubbing a credit card across the clear transfer tape. ...
3. Peel the paper backing off the sticker.
4. Place one end of sticker onto marked off spot firmly rubbing credit card or hard straight edge object across the clear transfer tape. ...
5. Once you feel decal is pressed firmly onto surface slowly peel back transfer paper off of the decal..... 
(if decal pulls away stop peeling and press down over that area with your nail or credit card then continue process slowly)  
2018 Pro Staff Program 

​Thank you for your interest in our Quick Draw Pro Staff program.
We have currently filled all positions for 2017.
We will start accepting resumes in Jan.2018 and choose Pro Staff in March.
Thanks for your support.
Bill 
Quick slick tape instruction:


  Clean rest launch pad with alcohol ,nail polish remover ,or any similar cleaning product . 
Cut 1/8x1inch strip from quick slick tape and attach to rest launch pad. Push down & rub with your finger to secure tape to rest . Using hot air from a blow dryer will soften the tape & let the glue stick better .
After a few seconds remove the hot air & again push down with finger & rub into place 

email me